Within our free Galaxy SDK for our industrial cameras , we offer a basic plugin to save captured images to the hard drive or to save the captured images as a video.In this article we explain the different settings and the settings we advise for capturing and saving images and videos using our industrial camera.
Videos and Images Save Plugin
Install our GalaxySDK ( Download drivers and manuals )
Run the program Daheng Galaxy Viewer(x64)
Go to Plugin->Videos and Images Save Plugin as shown in the screenshot below.
With this plugin captured images can be saved as images in different formats or even as a video file.
Base parameter for videos and Images Save Plugin
The following parameters can be set:
- Number of memory, the amount of images that are buffered into the...
Motion blur can cause the industrial camera to capture unsharp / blurry images. Unsharp images result in inaccurate measurements, bad fault detection or wrong classifications. Motion blur is caused by movement or vibration during the exposure time of the industrial camera. When the object moves for more than 0.5 pixel during the exposure time, the image will have motion blur.
To avoid motion blur, the shutter speed must freeze the scene, so the object does not move more than 0.5 pixel during exposure time. This can be done by reducing the exposure time of the camera. However, reducing the exposure time will also make the image darker (as there is less time to capture light).
Illustration of the effect of motion blur
How to make your setup more light sensitive
If your image is too dark you can check one of...
This article explains how to read barcodes and DMC codes (Datamatrix codes) with the most cost-effective machine vision camera solution. Additionally, we clarify the difference between Barcodes and DMC codes by discussing the pros and cons. We also provide a formula that helps you to calculate the required resolution, and give practical examples reading barcodes and DMC codes.
Barcode versus DMC codes
The best choice for code reading with industrial machine vision cameras is to use DMC codes instead of Barcodes. DMC codes can be read using lower resolution cameras while using the same field of view as Barcodes. Therefore, when reading DMC codes, you can use cheaper cameras. This also means that with DMC codes you can inspect a bigger field of view with the same hardware and price.
DMC code is a matrix of dots, also called a...
The Daheng Galaxy Viewer program is the main tool to test and program the camera. With Galaxy viewer it is possible to change and store camera parameters and to capture and store images. It has multiple plugins for additional features like crosshair, grid and LUT. We are going to show you the possibilities and how to use the Daheng Galaxy Viewer.
Step 1: Install the Daheng Camera machine vision SDK.
**Please don't connect the Machine Vision Camera before or during the SDK's installation**
You can find the latest version of our SDK in our download area . After downloading the SDK please install it, by running the file displayed to the right.
Once SDK is installed:
The software Galaxy viewer will be installed.
All camera documentation will be available in the folder: C:\Program Files\Daheng...
Global shutter is used for capturing moving objects, while rolling shutter is used for capturing still images. A rolling shutter camera is cheaper, especialy for resolutions above 1.6 Megapixel. A 12MP rolling shutter camera costs approx. 200 euro, while a 12MP global shutter costs approx. 1000 euro. A Global shutter has larger pixels, therefore a larger sensor as a rolling shutter camera. As a result, a global shutter camera is more light sensitive and produces sharper images.
Exposure and Shutter
Exposure time is a period of the shutter from open to close. During the period, the light exposing on the chip’s photosensitive array and Photoelectric effect occurs, then photoelectric charges are produced. By the A/D transformation, the grayscale value of each pixel is displayed. Under a certain light intensity, the...
You might have noticed that some of our cameras are marked as ‘GeT-Cameras Choice’. There are a few reasons why we recommend these cameras, like recommendation for new indesign, the newest image sensors and shorter lead times.
Recommended for new indesigns
The main reason why a camera is marked as ‘GeT Cameras Choice’ is because we recommend this camera for your new development. The camera is in an early stage of its product life cycle. Every camera is at least available for 7 years after market introduction. Our track record shows an average availability of 12-15 years. Read more about product life cycle on our machine vision knowledge center: Product life cycle of industrial cameras.
Newest image sensors
Additionally the image sensors of the cameras are one of the latest generations. Using the...
Gaspar van Elmbt, the managing director of GeT-Cameras, had planned to give a presentation about cost reducing vision hardware design at the UKIVA this month. However, due to the Covid’19 virus this event got cancelled. The organization of this event managed to provide the visitors with all the presentations, included ours, on the ‘presentation hub’.
If you want to learn how to reduce the cost price of your project, make sure to take a look at the presentation in the video below.
All our industrial cameras have a minimum life cycle of 7 years after market introduction. The graph below shows the typical product life cycle stages of an industrial camera.
Market introduction of an industrial camera
When a camera is released it has the latest generation sensor. In almost all cases the latest generation sensor is more light senstive and has less noise than previous generation sensors. Therefore a better image quality can be achieved.
Check for newer alternatives
After 3-7 years, sensor manufacturers will release a new version of the sensor or a sensor from a different brand might have better imaging performance. Therefore during this period it's important to check if there are other camera types available that have a newer image sensor.
Unfortunately cameras do go End of Life (EOL)....
Machine vision camera Interface whitepaper
This article will provide a deeper inside in what the benefits and downsides are of each type of machine vision camera interface, so you can select the right interface for your machine vision application. It has to be noted that GeT cameras only supplies USB 2.0 , USB 3.0 , GigE , 5GigE and 10GigE machine vision cameras and the article will mainly be focused on these five industrial machine vision interfaces. However in the table below we have incorporated also other interfaces to make the overview of industrial machine vision camera interfaces complete.
Arm embedded platforms are very popular for embedded vision. Many of these platforms have a USB2, USB3 and or GigE ethernet port. Our USB3 and GigE Vision Cameras work with these ARM embedded platforms. The Raspberry Pi, that has a USB2 port, even works with our USB3 cameras on reduced frame-rate .
Which embedded board to select with USB3 Vision Camera
There are many embedded boards available in the market that work with our USB3 Vision Cameras. The following ARM platforms were extensively tested with our machine vision cameras:
- NVIDIA Jetson TX1/TX2
- NVIDIA Tegra TK1
- Toradex Apalis TK1 on Ixora Carrier Board
- Raspberry Pi 3B, incl. support of the camera module.
However other popular embedded boards are:
- Odroid XU4
- NanoPi M4
- NVIDIA Jetson Nano
We especially like the Raspberry Pi for low end...
Industrial Polarized Camera
Daheng Imaging is dipping their toes in the industrial polarized camera segment by implementing the Sony-IMX250MZR monochrome image-sensor . The Industrial polarization camera systems are able to capture information which a normal line or area industrial camera is not able to obtain. A polarization camera conducts a two-dimensional analysis. It measures both the degree and direction of the polarization of the light. As a result the final image has almost none reflections from external lightsources. A polarized camera is ideal for applications like the inspection of glossy products and transparent products.
Standard machine vision camera versus polarized camera
The following examples show on the left hand side an image captured with a standard machine vision camera and on the right...
Introduction to the industrial machine vision USB3 Camera System
USB3 Vision standard is an imaging interface standard for industrial USB3 vision cameras . The majority of camera manufacturers have already adopted this standard, and the number of compatible, accessories growing quickly. A big advantage of the USB3 interface is that, any of the PCs, laptops and smartphones have a USB 3.0 interface built in nowadays. In the field of vision technology, USB 3.0 is also replacing dated interfaces such as the FireWire, Cameralink and USB2.0.
The speed of the USB3 Vision Camera Interface
The USB 3.0 interface, also known as Super-Speed USB, is the following line of the well-known plug and play Universal Serial Bus spec that builds on the assets of USB 2.0 and washed out its weaknesses. The operative bandwidth accessible with the...