Account

Je bent momenteel nog niet ingelogd.

Inloggen

Machine vision knowledge center

GET racing - GeT Cameras Collaboration

  Machine vision market & applications     26-02-2024  

GET racing, the Formula Student team of the Technical University Dortmund, joined a collaboration with GeT Cameras to enhance their autonomous racing capabilities. GET racing started competing in early 2022,  they spent their first years competing with combustion vehicles and have since then transitioned to electric racing cars. To improve their performance on the race track, two cameras from GeT Cameras were installed on top of the car. The team implemented two highspeed MER2-160-75GC-P cameras with the SONY IMX273 sensor . The Formula Student competition Formula Student is an international engineering competition where university teams design and build race cars to compete in different disciplines. The GET racing student team has been taking part in this competition since 2005. With a total of eleven cars built, 2023 was...

Lees meer

UMD Racing - GeT Cameras Collaboration

  Machine vision market & applications     16-02-2024  

UMD Racing, a student-run organization dedicated to the development of electric race cars, they have been actively participating in the Formula Student competitions. During multiple yearly events, the team aims to design and manufacture a high performance car to compete against other student teams. The team’s vision to compete in the driverless category encouraged them to reach out to GeT Cameras for camera hardware. Their focus on innovation and performance made them choose the MER2-041-528U3C camera , equipped with the SONY IMX287 sensor . Sponsorship The decision to collaborate with GeT Cameras was affected by the clear and transparent website and competitive pricing. As well, the students of UMD Racing were looking for specific requirements such as a high frame rate. One of the highspeed machine vision cameras of GeT...

Lees meer

How the European Vision camera market got disrupted

  Machine vision market & applications     19-12-2023  

Many years the European camera manufacturers dominated the machine vision camera market worldwide. Time is changing and Chinese camera manufacturers are entering the European market. Only a few Chinese camera manufacturers, like Daheng Imaging , can offer high quality products for a low price. European vision camera manufacturers can’t compete on price because the Chinese camera manufacturer have the following competitive advantages: No overhead features. Most Chinese vision cameras have standard features like exposure, gain, white balance control, etc, but no advanced features like pixel binning and skipping. By reducing the amount of advanced features, less development time and less expensive FPGA's (Hardware) is needed. This results in lower cost price per camera Scale of Economy. China is the largest...

Lees meer

Quality mark to safely purchase machine vision cameras online

  Machine vision market & applications     19-12-2023  

Quality mark to safely purchase machine vision camera s online GeT Cameras, the webshop for industrial machine vision cameras , is now associated with the webshop quality mark WebwinkelKeur and EMOTA (European eCommerce & Omni-Channel Trade Association). This is beneficial for both GeT Cameras and for you as our customer. With this quality mark we are creating a trustworthy environment for the purchase of a machine vision camera. Namely, the quality mark offers different guarantees and the option for you, as the customer, to leave a review about your experience with our machine vision camera and our services. Your opinion about our machine vision camera is valued As aforementioned gives the quality mark the option to the customer to leave his/ her review regarding our services and their experiences with our...

Lees meer

Upcoming Fairs 2020

  Machine vision market & applications     19-12-2023  

One of the Key values of GeT-Cameras is contributing to technological projects by offering fair priced machine vision and provide you with excellent service. To show our devotion to this key value we would like to meet you on the following Machine Vision events: UKIVA: 14 May 2020 (Cancelled) Due to the rapidly spreading COVID-19 virus, the organisation of UKIVA has announced to cancel this congress. This means that we will not be meeting you the 14 th of May. Luckily, there is still a chance to see the presentation of our managing director Gaspar van Elmbt. We will be uploading this presentation to the technology presentation hub of UKIVA, and on the 14 th of May, this presentation will be visible for your viewing. The presentation is also available here . Vision, Robotics & Motion...

Lees meer

New waterproof aluminium enclosure

  Machine vision market & applications     19-12-2023  

Protect your machine vision camera against moisture and dust with GeT Cameras’ newest aluminium camera enclosure . Why is it important to protect your machine vision hardware? With an industrial camera enclosure, your machine vision solution will be more robust. A camera enclosure protects your machine vision cameras and lenses from harsh environmental conditions. Water and dust can damage your camera and taint the image quality. A camera enclosure provides a protective barrier which prevents the camera from damage.  Features of the GeT Cameras aluminium camera enclosure •    Designed to comply with IP67 standards •    Supports machine vision cameras (29x29mm) from a variation of well-known manufacturers •    The modular design supports...

Lees meer

  Machine vision market & applications     19-12-2023  

Machine Vision Application in the Pharmaceutical Industry Pharmaceutical industry is a quality critical industry because it has close ties with people's life and health. A Vision inspecting system is often applied on the assembly line. The typical inspected objects usually include capsule, injection, bubble cap, label of the package and etc. All Daheng Imaging cameras undergo thorough critical tests to ensure that they can meet the industrial and professional requirements under the tough conditions. Pharmaceutical production usually does not take place in a comfortable lab, but reliable inspection results in a tough environment are a guarantee for the drug quality. To get the reliable inspection results, Daheng Imaging cameras offer outstanding quality images with high-performance digital interfaces , as well as rapid trigger...

Lees meer

Formula Electric driverless competition

  Machine vision market & applications     19-12-2023  

. Formula Electric Belgium is preparing for driverless competition with dual head stereo vision camera from GeT-Cameras. Competition The Formula Electric Belgium team, consisting of 25 Belgian university students, are building their first autonomous Formula car. In the previous years, the team joined in the electric competition along with more than 50 other competitors. This year they decided to enroll in the autonomous competition once more to inspire people with the possibilities of electric and driverless cars. Their Formula racecar competes in multiple disciplines, acceleration, grip strength and endurance. With exactly 1000 collectable points, the team strives to win this year’s competition. For acceleration, the car has to get from standstill to the 75-meter finish line as quickly as possible; Next, the car gets...

Lees meer

World Creativity and Innovation Day 2021

  Machine vision market & applications     19-12-2023  

The United Nations marks April 21 st as World Creativity and Innovation Day . World Creativity and Innovation Day originated in 2002 because both creativity and innovation have been acknowledged as true wealth of nations in the 21 st century. Creativity and innovation are the cornerstones of the digital revolution which characterizes itself by technology quickly advancing and replacing older tech at an exponential rate. During World Creativity and Innovation Day we would like to thank all of you, who use our industrial cameras to create awesome vision solution all around the world. It excites us that our customers find many creative ways to use our machine vision products. You inspire us to push ourselves to create affordable and unique machine vision components to make your workflow easier and quicker. We have designed some...

Lees meer

  Machine vision market & applications     19-12-2023  

Now that the situation regarding the pandemic seems to be improving, we are able to meet you at some exhibitions this year. We hope to see you there.   UKIVA Machine Vision Conference 2022 April 28th, Milton Keynes, UK Last time we were going to be exhibiting the UKIVA Machine Vision Conference, the event got cancelled due to the global pandemic. This year we are optimistic that we have a shot at redeeming ourselves. Come find us the 28th and see our newest machine vision cameras on display Vision, Robotics & Motion 2022 June 8th & 9th, Den Bosch, NL At Vision, Robotics & Motion 2022, themes like vision, optics, robotic, motion control and data science are getting highlighted. Vision 2022 October 4th, 5th &6th, Stuttgart, DE Last year, we were happy to be able to go to the Vision Conference in...

Lees meer

GeT Cameras official member of SPIE

  Machine vision market & applications     19-12-2023  

SPIE (the international society for optics and photonics) is a non-profit organization dedicated to advancing the scientific research and engineering applications of optics and photonics. From now on GeT Cameras is officially a member of SPIE. What does SPIE do? Founded in 1955, SPIE has the advancement of light-based technologies as purpose. They achieve this by interdisciplinary information exchange and educating by hosting and sponsoring of technical forums, trade shows and educational programs. They will host the SPIE Photonics West vision fair. GeT Cameras will exhibit at this vision fair in San Francisco, California from January 31st until the 2nd of February.  

Lees meer

Upcoming Machine Vision Exhibitions 2023

  Machine vision market & applications     19-12-2023  

GeT Cameras attends multiple machine vision exhibitions and trade fairs ever year. This year we will be able to meet with you and discuss camera requirements for machine vision applications at 5 different exhibitions. SPIE Photonics West 28 January – 2 February | San Francisco, CA - United States of America Meet our Philadelphia office on their first trade fair at SPIE Photonics West. We will be displaying our latest camera models, lens portfolio and machine vision lights. Our booth number is 158! Automate Detroit 22 May – 25 May | Detroit, MI - United States of America For the first time, GeT Cameras will attend “Automate” in Detroit, MI. We hope to meet you there and talk to you about industrial automation. Vision, Robotics & Motion 7 June – 8 June | Den Bosch, The Netherlands...

Lees meer

GeT Cameras official Member of A3 Automate

  Machine vision market & applications     19-12-2023  

GeT Cameras is officially a member of the Association for Advancing Automation (A3). A3 is North America’s largest automation trade association with a focus on Machine Vision. GeT Cameras is now part of the 1,100 members of the A3. What does A3 do? A3 sponsors trade shows, conferences, and other networking events. It collects industry statistics; generate market research and they develop market standards and certifications. A3 host the Automate Show in Detroit, USA and The Vision Show in Boston. Both shows display many machine vision products and competences. We are happy to meet you on these trade shows to discuss your products and show you our strong and reliable industrial cameras.   

Lees meer

Penn Electric Racing - GeT Cameras collaboration

  Machine vision market & applications     19-12-2023  

Penn Electric Racing is a student run organization dedicated to building electric racecars. Every year, the team competes with other student-built racecars in the Formula SAE , an international competition for university teams to design and manufacture the best performing racecars.   Their ambition is to gain experience and compete in the autonomous competition in the future as well. To achieve these ambitions, Penn Electric Racing reached out to GeT Cameras. They were looking for compact industrial cameras online and came across our global shutter MER2-160-227U3C with the SONY IMX273 image sensor. Sponsorship Penn Electric Racing got in touch with GeT Cameras because of the clear website and competitive pricing. “GeT Cameras had the camera prices displayed on the website which was nice for orientation. Because of...

Lees meer

Smart camera vs. PC-connected industrial camera

  Machine vision market & applications     19-12-2023  

Are you looking for the right camera system for your industrial automation or visual inspection application? GeT Cameras offers a wide portfolio with more than 200 industrial cameras.  Our cameras should be connected with a cable to a PC. Compared to smart cameras, industrial cameras are a better solution. There are 3 main advantages:  1.    Cost-effective solution PC-connected industrial cameras offer a much more affordable solution, especially for projects where multiple cameras are being used. Our PC-connected industrial cameras start at € 115 per piece. In contrast, smart cameras often come with a high price tag because of their specialized hardware. 2.    Rapid image processing When it comes to image processing, an industrial PC is much more powerful than a smart camera. PCs have...

Lees meer

Explanation USB3 Vision camera protocol | Top 5 reasons why to use an industrial USB3.0 camera

  Vision Hardware Selection     19-12-2023  

USB3 Vision standard is an imaging interface standard for industrial USB3 vision cameras. The majority of camera manufacturers have already adopted this standard, and the number of compatible accessories is growing quickly. A big advantage of the USB3 interface is that, any of the PCs, laptops and smartphones have a USB 3.0 interface built in nowadays. In the field of vision technology, USB 3.0 is also replacing dated interfaces such as the FireWire, Cameralink and USB2.0. The speed of the USB3 vision camera interface The USB 3.0 interface, also known as Super-Speed USB, is the following line of the well-known plug and play Universal Serial Bus spec that builds on the assets of USB 2.0 and washed out its weaknesses. The operative bandwidth accessible with the use of USB 3.0 when transferring bulks of data totals 350-450 MB/s,...

Lees meer

NEW Custom machine vision lens filters

  Machine vision market & applications     19-12-2023  

We have expanded our lens filter portfolio with many new custom-made lens filters. Choose from a wide variety of lens filters such as longpass, bandpass and polarizing filters:  Lens filter portfolio . What are machine vision lens filters? Lens filters can be used to improve the quality and accuracy of your image processing. We offer a variety of filters, each serving a different purpose. For example, bandpass filters are being used when only a specific wavelength should pass the light filter. Each special filter allows a specific range of wavelengths to pass and block. These could be used in applications where for example glare reduction, colour correction or UV/ IR filtering is required.   How to order your lens filters? 1.    Go to our  custom lens filters product page ....

Lees meer

Industrial polarization camera whitepaper

  Vision Hardware Selection     19-12-2023  

Daheng Imaging is familliar in the industrial polarized camera   segment by implementing the Sony-IMX250MZR monochrome image-sensor . Recently the IMX264MZR has also been added to the portfolio. The Industrial polarization camera   systems are able to capture information which a normal line or area industrial camera is not able to obtain. A polarization camera conducts a two-dimensional analysis. It measures both the degree and direction of the polarization of the light. As a result the final image has almost none reflections from external lightsources. A polarized camera is ideal for applications like the inspection of glossy products and transparent products. Standard Machine vision camera versus polarized camera The following examples show on the left hand side an image captured with a standard machine vision...

Lees meer

Raspberry Pi with 20MP industrial camera

  Vision Hardware Selection     19-12-2023  

Arm embedded platforms are very popular for embedded vision. Many of these platforms have a USB2, USB3 and or GigE ethernet port. Our USB3 and GigE Vision Cameras work with these ARM embedded platforms. The Raspberry Pi, that has a USB2 port, even works with our USB3 cameras on reduced frame-rate . Which embedded board to select with a USB3 Vision Camera There are many embedded boards available in the market that work with our USB3 Vision Cameras. The following ARM platforms were extensively tested with our machine vision cameras: NVIDIA Jetson TX1/TX2 NVIDIA Tegra TK1 Toradex Apalis TK1 on Ixora Carrier Board Raspberry Pi 3B, incl. support of the camera module. However other popular embedded boards are: - Odroid XU4 - NanoPi M4 - NVIDIA Jetson Nano - Firefly The Raspberry Pi is prefered...

Lees meer

Product life cycle of industrial cameras

  Vision Hardware Selection     19-12-2023  

All our industrial cameras have a minimum life cycle of 7 years after market introduction. The graph below shows the typical product life cycle stages of an industrial camera. Market introduction of an industrial camera When a camera is released it has the latest generation sensor. In almost all cases the latest generation sensor is more light senstive and has less noise than previous generation sensors. Therefore a better image quality can be achieved. Check for newer alternatives After 3-7 years, sensor manufacturers will release a new version of the sensor or a sensor from a different brand might have better imaging performance. Therefore during this period it's important to check if there are other camera types available that have a newer image sensor. EOL Notification Unfortunately cameras do go End of Life...

Lees meer

Vision hardware design rules to reduce the cost price of your project

  Vision Hardware Selection     19-12-2023  

Gaspar van Elmbt, the managing director of GeT-Cameras, had planned to give a presentation about cost reducing vision hardware design at the UKIVA this month. However, due to the Covid’19 virus this event got cancelled. The organization of this event managed to provide the visitors with all the presentations, included ours, on the ‘presentation hub’.   If you want to learn how to reduce the cost price of your project, make sure to take a look at the presentation in the video below.    

Lees meer

What does ā€˜GeT Cameras Choiceā€™ mean?

  Vision Hardware Selection     19-12-2023  

You might have noticed that some of our cameras are marked as ‘GeT-Cameras Choice’. There are a few reasons why we recommend these cameras, like recommendation for new indesign, the newest image sensors and shorter lead times.   Recommended for new indesigns The main reason why a camera is marked as ‘GeT Cameras Choice’ is because we recommend this camera for your new development. The camera is in an early stage of its product life cycle. Every camera is at least available for 7 years after market introduction. Our track record shows an average availability of 12-15 years. Read more about product life cycle on our machine vision knowledge center: Product life cycle of industrial cameras. Newest image sensors Additionally the image sensors of the cameras are one of the latest generations. Using the...

Lees meer

How to select camera and software for Barcode and DMC code reading

  Vision Hardware Selection     19-12-2023  

This article explains how to read barcodes and DMC codes (Datamatrix codes) with the most cost-effective machine vision camera solution. Additionally, we clarify the difference between Barcodes and DMC codes by discussing the pros and cons. We also provide a formula that helps you to calculate the required resolution, and give practical examples reading barcodes and DMC codes. Barcode versus DMC codes The best choice for code reading with industrial machine vision cameras is to use DMC codes instead of Barcodes. DMC codes can be read using lower resolution cameras while using the same field of view as Barcodes. Therefore, when reading DMC codes, you can use cheaper cameras. This also means that with DMC codes you can inspect a bigger field of view with the same hardware and price. DMC code is a matrix of dots, also called a...

Lees meer

How to avoid motion blur

  Vision Hardware Selection     19-12-2023  

Motion blur can cause the industrial camera to capture unsharp / blurry images. Unsharp images result in inaccurate measurements, bad fault detection or wrong classifications. Motion blur is caused by movement or vibration during the exposure time of the industrial camera. When the object moves for more than 0.5 pixel during the exposure time, the image will have motion blur. To avoid motion blur, the shutter speed must freeze the scene, so the object does not move more than 0.5 pixel during exposure time. This can be done by reducing the exposure time of the camera. However, reducing the exposure time will also make the image darker (as there is less time to capture light). Illustration of the effect of motion blur How to make your setup more light sensitive  If your image is too dark you can check one of...

Lees meer

Should you upgrade your webcam to an industrial camera?

  Vision Hardware Selection     19-12-2023  

Upgrading from a webcam to an industrial machine vision camera brings a lot of benefits in terms of image quality, performance, and functionality. In this article, we will discuss the advantages of using an industrial machine vision camera and how it differs from a webcam. The differences between a webcam and an area scan camera Webcams are common in many applications, from video conferencing to streaming. They are relatively inexpensive and easy to use, but they have limited functionality and lower image quality compared to industrial machine vision cameras. Industrial machine vision cameras are designed for applications that require high-quality images, high-speed imaging, and advanced features. They are widely used in industries such as manufacturing, automation, robotics, and quality control. The purpose of a webcam is to...

Lees meer

Exploring Telecentric Lighting in Machine Vision Systems

  Vision Hardware Selection     19-12-2023  

In the world of machine vision systems, achieving accurate and reproduceable image quality is crucial for tasks such as inspection, measurement, and quality control. Telecentric lenses and telecentric lighting play vital roles in enhancing imaging precision. In this article, we will give a brief introduction to telecentric lenses, then delve into the advantages and disadvantages of telecentric lighting. Additionally, we will explore the parallel backlight as an alternative lighting solution in certain scenarios. If you need any support, or you are interested in our telecentric lenses and lighting, please contact us below. Our website only shows a limited part of our complete portfolio of telecentric lenses and lighting, which can be found here: Telecentric lens portfolio . hbspt.forms.create({ region: "na1",...

Lees meer

Polarization in your machine vision application

  Vision Hardware Selection     19-12-2023  

This article explores the basics of polarization and how it can be applied in diverse machine vision applications. Additionally, it places focus on cross-polarization; an advanced technique that enhances image quality by minimizing glare and revealing hidden details. Are you currently working on an application involving surface inspection, experiencing issues with glare or needing some advice on a similar application? We can assist with the selection of the right polarization hardware.  What exactly is polarization in machine vision? Polarization aligns the orientation of light waves towards a specific direction. It offers machine vision systems a unique tool that can extract information from a scene that is invisible when using conventional imaging methods. Polarization-based techniques add a new layer of contrast and detail,...

Lees meer

Quickstart, 5 steps to trigger LED from Vision Camera using strobe controller

  Camera & Vision techniques     19-12-2023  

How to connect and trigger a LED light source with a machine vision camera from Daheng Imaging using an industrial strobe controller . This is applicable to both USB3 and GigE machine vision cameras that have a trigger output. As additional hardware we have used a 12V powersupply, a Power LED and a triggerable industrial strobe controller, the ACC-MV-LED-STROBECONTROLLER-V1 . We have recently renewed this article on the product page of the industrial strobe controler .   Step 1: Program the triggerable industrial strobe controller We are using in our example an ACC-MV-LED-STROBECONTROLLER-V1 industrial strobe controller that can be triggered. A nice feature of this strobe controller is that you can program it, using the dipswitches, without the need of connecting the strobe controller to a pc....

Lees meer

Connecting multiple GigE cameras to one ethernet port

  Camera & Vision techniques     19-12-2023  

How do I connect multiple GigE industrial cameras to a single network port? We will explain how to connect 4 industrial GigE cameras. Therefore we have used the following material: 4x MER-630-16GC-P, 6.3MP industrial GigE camera 5 Port PoE switch 1000mbit / 1Gbit PC with windows 10 and a 1000mbit / 1Gbit networkcard Please double check that your connection is 1000mbit / 1Gbit and not 100mbit. Some PoE switches are only 100mbit and we see more often that customer think they have 1Gbit connection but in reality they have a 100mbit connection. This article explains how you can check if you have a 1 Gbit connection. You can only check this when the industrial GigE camera is connected. Step 1,  connect all GigE cameras to the PoE switch Connect the GigE cameras to the PoE switch and check if the LED on the...

Lees meer

Hardware trigger cameras, master and slave(s)

  Camera & Vision techniques     19-12-2023  

How to synchronize industrial machine vision cameras? To synchronize industrial machine vision cameras the I/O port of the industrial camera is required. A master camera will hardware trigger it’s slave cameras to assure perfect synchronization between all cameras. In this example we explain how to connect 1 master camera to 3 slave cameras. As a result the setup will have 4 industrial cameras perfect synchronized. Technical schematic of a synchronized camera setup: The schematic below shows how to trigger 3 slave cameras from 1 master camera. An external power supply is always required. The external power supply voltage range should be between 5 and 24V. In our example we will use a 12V external power supply for the synchronized camera setup. The power Line 1 output can withstand 25 mA max. A Line 0 input(s) needs...

Lees meer

How to save the camera parameters in 3 steps

  Camera & Vision techniques     19-12-2023  

When you have set the parameters of your camera according to your application requirements, you can store these settings into the camera. When you reboot the camera, or reapply power to the camera, the camera will now start with your saved settings. STEP 1: CAMERA “UserSetControl” SETTINGS Open the GalaxyView software and connect to the camera. Go to the menu UserSetControl. When the camera is connected for the first time, the “Default” usersetting is already selected. You can change the following parameters: UserSetSelector -> choose which usersettings you want to select UserSetLoad -> load the selected usersettings UserSetSave -> Save the current camera settings into the selected usersetting UserSetDefault -> select which usersetting starts at camera boot STEP 2: SAVE YOUR...

Lees meer

How to use Power over Ethernet (PoE) with a GigE camera?

  Camera & Vision techniques     19-12-2023  

This article will explain 4 different ways to power a GigE camera. We talk about powering the industrial camera via a PoE Switch, PoE Injector, GigE Power adapter and via an external power source. The MER2 series power specifications are: PoE (Power over Ethernet, IEEE802.3af compliant) or 12VDC-10% ~ 24VDC+10% supplied via the camera's 8-pin Hirose connector. The MER series power specifications are: PoE (Power over Ethernet, IEEE802.3af compliant) or 12VDC-10%  supplied via the camera's 8-pin Hirose connector.   How to use Power over Ethernet with a PoE switch and a GigE PoE industrial Camera? A Power over Ethernet switch transmits power and data via a CAT6 network cable. This means that if your machine vision application has a GigE industrial camera with PoE, you do not need an extra external power...

Lees meer

How to set a Region of Interest (R.O.I.) inside an industrial camera in 3 steps

  Camera & Vision techniques     19-12-2023  

This guide will explain how to set and use the Region of interest function of the industrial camera, how to resize an image and how to capture only a defined area. This is commonly used to: -    reduce the amount of collected data -    reduce the required bandwidth -    increase the framerate of an industrial camera -    isolate the view on a certain area In this article we will set a Region of Interest and offset it from the top left corner to the centre of our image. Using these 3 steps you can define the size and position of the industrial cameras Region of Interest. STEP 1: CHECK THE IMAGE SIZE AND DEFINE REGION OF INTEREST Check the maximum image size (resolution) of your industrial camera and define your desired Region of Interest. For this...

Lees meer

How to control the bandwidth use of an industrial USB3 camera by limiting its framerate

  Camera & Vision techniques     19-12-2023  

Bandwidth is the amount of data which can be transmitted over a certain interface (USB3 / GigE / 5GigE) during a certain period. The higher the bandwidth of the interface, the more and faster data can be received or sent. This article will explain multiple options for bandwidth control and how to calculate the required framerate for your industrial USB3 camera. To control the bandwidth of industrial USB3 cameras, we need to understand how the USB3 connection works and how to determine which framerate values we need. USB3 INDUSTRIAL VISION CAMERA ADVANTAGES USB3 is a suitable interface for high resolution and high-speed cameras. The USB3 connection has a maximum bandwidth of 480 megabytes per second. This is 10 times faster than USB2 and 4 times faster than GigE. Every computer and almost all developer boards come with USB3...

Lees meer

Hoe de framerate calculator voor industriĆ«le cameraā€™s te gebruiken

  Camera & Vision techniques     19-12-2023  

Om de framerate van een industriële camera te berekenen, is een framerate calculator beschikbaar. Dit document was beschikbaar na het installeren van de SDK. De framerate calculator (een Excel-bestand) bevond zich in de map C:\Program Files\Daheng Imaging\GalaxySDK\Doc. Momenteel kunt u de framerate calculator eenvoudig downloaden van onze download omgeving. . Voor dit voorbeeld gebruiken we de framerate calculator voor de USB3 camera MARS-1230-23U3X om de verschillende beschikbare opties uit te leggen. Daarna zullen we de paar verschillen tussen een USB3-camera en een Gigabit Ethernet framerate calculator toelichten. Voor de Gigabit Ethernet camera gebruiken we de MER-131-75Gx camera als voorbeeld.4 Stap 1: open de frame rate calculator voor usb3 camera’s Open de juiste framerate calculator. Elke cameraserie...

Lees meer

I/O Control: Hoe u een machine vision camera hardwarematig kunt triggeren met een triggersencor en hoe u machine vision verlichting kunt triggeren

  Camera & Vision techniques     19-12-2023  

Industriële machine vision-camera’s zijn betrouwbaar en robust, dus moet het externe triggersysteem dat ook zijn. Wanneer een snelle werking nodig is, moet de triggersensor zeer snel reageren. De triggersensor verandert de spanning (elektriciteit) op de gespecificeerde pinnen van de I/O-connector van de camera. Dit system werkt met de zogenaamde rising edge of falling edge, spanning die van een lage waarde naar hoog gaat (rising edge), of van hoog naar lag (falling edge). Hierdoor zal de camera zeer snel reageren op de triggers van de triggersensor. De camera programmeren om triggers van de triggersensor te accepteren U kunt een machine vision camera programmeren om triggers van de triggersensor te accepteren. Als u onze camera’s gebruikt, moet u onze Galaxy SDK-software gebruiken. Wanneer u verbonden bent...

Lees meer

Pixel binning, Decimation (pixel skipping), Gamma en Digital Shift uitgelegd

  Camera & Vision techniques     19-12-2023  

Pixel binning en Decimation zijn geavanceerde camerafuncties die beschikbaar zijn op bepaalde camera’s. Om te controleren of deze functie beschikbaar is voor uw camera, opent u de framerate calculator zoals uitgelegd in dit artikel: https://www.get-cameras.com/How-to-use-the-frame-calculator-for-industrial-cameras en controleert of u het veld ‘BinningHorizontal’, ‘BinningVertical’, ‘DecimationHorizontal’ en ‘DecimationVertical’ zichtbaar zijn in de framerate calculator voor uw cameramodel. Pixel binning wordt gebruikt om de lichtgevoeligheid te verhogen en de beelresolutie te verlagen. Decimation, ook bekend als ‘pixel skipping’, wordt gebruikt om de beeldresolutie te verlagen zonder de grootte van het gezichtsveld te veranderen.  Pixel binning ...

Lees meer

Afbeeldingen en videoā€™s opslaan met een industriĆ«le camera & Galaxy SDK

  Camera & Vision techniques     18-12-2023  

Binnen onze gratis Galaxy SDK voor onze industriële camera’s bieden we een basisplugin om vastgelegde beelden op te slaan op de harde schijf of om de vastgelegde beelden op te slaan als video. In dit artikel leggen we de verschillende instellingen uit en de instellingen die we adviseren voor het vastleggen en opslaan van beelden en video’s met onze industriële camera. Video’s en afbeeldingen opslaan plugin Installeer onze GalaxySDK ( Download stuurprogramma’s en handleidingen ) Start het programa Daheng Galaxy Viewer (x64) Ga naar Plugin -> Video’s en afbeeldingen opslaan. Plugin zoals in de schermafbeelding hieronder. Met deze Plugin kunnen gemaakte afbeeldingen worden opgeslagen als afbeeldingen in verschillende formaten of zelfs als een videobestand.  ...

Lees meer

Hoe installeerd u uw camera op de mvec167 industriƫle behuizing

  Camera & Vision techniques     18-12-2023  

Welkom bij de stap-voor-stap instructies voor het installeren van een industriële camera op de MVEC167 industriële camerabehuizing. Als u op enig moment tijdens de instructie vragen heeft, bel of mail ons dan op cs@get-cameras.com en ons team helpt u verder. We wensen u veel succes met de installatie. GeT Cameras support: Selecteer de behuizing die geschikt is voor uw machine vision-toepassing.   hbspt.forms.create({ region: "na1", portalId: "7372172", formId: "fec74822-b8b0-4920-92a8-ce596b5738a6" }); Stap 1: voorbereidingen Pak de MVEC167 uit op een veilige plek, want hij bevat schroeven en losse onderdelen. Pak een Torx T10 schroevendraaier, uw industriële camera, de lens en kabels Stap 2: verwijder de lensbuis Til de blauwe pin aan de...

Lees meer

Cameraparameters optimaliseren voor detectie van bewegende objecten

  Camera & Vision techniques     18-12-2023  

Toepassingen met snel bewegende objecten hebben vaak een hoge framerate en een korte belichtingstijd nodig. Een korte belichtingstijd gaat gepaard met minder licht, wat betekent dat een lichtgevoelige lens en beeldsensor nodig zijn. Hier volgt een overzicht van instellingen die u zullen helpen om de optimale instellingen te vinden voor uw hogesnelheidstoepassing. U kunt dit als richtlijn gebruiken. Stel de juiste belichtingstijd in De eerste instelling om te optimaliseren is de belichtingstijd. De maximale belichtingstijd is 1/framerate. Als u 200 fps wilt bereiken, is de maximale belichtingstijd 1/200= 5 ms. Hoe lager de belichtingstijd, hoe donkerder het beeld. Daarom wilt u de belichtingstijd zo lang mogelijk maken om de helderheid te verhogen. Dit wordt echter beperkt door de berekende maximale belichtingstijd zoals...

Lees meer

Hoe gebruik je scherptediepte (Depth of Field) tot je voordeel?

  Camera & Vision techniques     18-12-2023  

Depth of field (ook wel scherptediepte genoemd) is belangrijk voor het maken van een scherp beeld van een object dat u inspecteert. Met het juiste gebruik van de depth of field kunt u ervoor zorgen dat het object dat u inspecteert scherp is, terwijl de achtergrond en voorgrond niet scherp/wazig zijn. Zo is het voor uw visiesoftware gemakkelijker om uw object te herkennen. Depth of field is een belangrijke factor die u in uw voordeel kunt gebruiken. Dit artikel legt uit wat depth of field is en hoe u het kunt toepassen. Wat is depth of field? Technisch gezien is depth of field de afstand tussen het dichtstbijzijnde en verst gelegen object in de afbeelding dat tijdens de eerste foto scherp is. In onderstaande afbeelding is de werkafstand 250mm. Het dichtstbijzijnde object bij de lens is hier 190 mm van verwijderd. Het verst gelegen...

Lees meer

Gamma voordelen in machine vision

  Camera & Vision techniques     15-12-2023  

Gamma is een machine vision techniek die wordt gebruikt om het verschil tussen de digitale beeldgegevens en de perceptie van het menselijk oog te corrigeren. Het kan ook worden gebruikt om overbelichte plekken aan te passen en te verbeteren. Dit is een uitgebreid artikel over Gamma correctie. Wat is gamma correctie? Een camera sensor converteert de lichtintensiteit van een pixel naar een gelijke digitale waarde. De digitale waarde is recht evenredig met de lichtintensiteit van een pixel en heeft dus een lineaire relatie. Het menselijk oog neemt beelden waar als een logaritmische functie van de intensiteit, in plaats van een lineaire functie. Als de beelden van een camerasensor direct op een weergaveapparaat worden weergegeven, zal de scene onnatuurlijk lijken vanwege de ongelijkheden tussen de camerasensor en de waarneming van het...

Lees meer

Hoe importeer of exporteer je industriƫle camera-instellingen?

  Camera & Vision techniques     15-12-2023  

Dit artikel legt uit hoe u de parameterinstellingen van uw camera naar een tekstbestand kunt exporteren. Het bestand kunt u gebruiken om de instellingen te herstellen, verschillende instellingen tijdens het testen te documenteren of meerdere camera's met dezelfde instellingen te configureren. Waarom camera-instellingen importeren of exporteren? De GalaxyViewer heeft de optie om de huidige instellingen van de camera op te slaan in een tekstbestand. Deze functie kan nuttig zijn in bepaalde gevallen, zoals wanneer u verschillende camera-instellingen test en deze wilt vastleggen of wanneer u technische ondersteuning nodig heeft. Het tekstbestand kan ook worden geïmporteerd in Excel voor verdere analyse. Hoe worden de industriële camera settings geëxporteerd? Het exporteren van de instellingen van een...

Lees meer

Hoe de Linux SDK te downloaden, installeren en uitvoeren die geschikt is voor ARM-gebaseerde hardware zoals Raspberry Pi of Nvidea Jetson

  Camera installation instructions     14-12-2023  

Dit artikel legt uit hoe u de Linux Galaxy Software Development Kit (SDK) voor ARM-gebaseerde hardware kunt downloaden, installeren en gebruiken. Met deze SDK kunt u industriële cameraparameters aanpassen en beelden opvragen van onze USB3 en GigE camera’s. Kleine ontwikkelboards zoals Nvidia Jetson-serie en de Raspberry Pi zijn getest met onze camera’s. De afbeeldingen in dit artikel zijn van verschillende ontwikkelboards met Linux. De layout kan op uw computer verschillen. Stap 1: Download de Linux Galaxy SDK Op onze downloadpagina zijn meerdere versies van de Linux Galaxy SDK beschikbaar. Zorg ervoor dat u de juiste downloadlink kiest, die geschikt is voor de architectuur van uw computer hardware (zie onderstaande schermafbeelding). Voor ARM-hardware download u de Linux ARM SDK, nummer 6 in de...

Lees meer

Hoe u in 3 stappen de Linux Galaxy SDK kunt downloaden, installeren en uitvoeren die geschikt is voor uw industriƫle camera hardware

  Camera installation instructions     14-12-2023  

In dit artikel wordt uitgelegd hoe u de Linux Galaxy Software Development Kit (SDK) kunt downloaden, installeren en gebruiken. Met deze SDK kunt u uw industriële cameraparameters aanpassen en beelden opvragen van onze camera’s. U kunt dit programma uitvoeren op X86- of ARM- hardware, zoals computers of kleine ontwikkelingsborden zoals de Nvidia Jetson-serie en de Raspberry Pi. De afbeeldingen in dit artikel zijn van een X86 industrieel ontwikkelbord, waarop Linux draait (Ubuntu 20.04). Na het volgen van deze 3 stappen kunt u de Galaxy View SDK downloaden, installeren en gebruiken op Linux. Stap 1: Download de Linux Galaxy SDK Op onze downloadpagina zijn meerdere versies van de Linux Galaxy SDK beschikbaar. Zorg ervoor dat u de juiste downloadlink kiest, die geschikt is voor de architectuur van uw computerhardware (zie...

Lees meer

Hoe compileer ik een C# voorbeeldprogramma om beelden te verkrijgen in Visual Studio?

  Camera installation instructions     14-12-2023  

Microsoft Visual Studio is een geïntegreerde ontwikkelomgeving van Microsoft. Het wordt onder andere gebruikt voor het ontwikkelen van verschillende software programma’s. De basis editie van Visual Studio, de Community-editie, is gratis beschikbaar. Visual Studio ondersteunt 36 verschillende programmeertalen en de code editor en debugger ondersteunen (in verschillende mate) bijna elke programmeertaal. Ingebouwde talen zijn onder andere C, C++, C++/CLI, Visual Basic .NET, C#. Ondersteuning voor andere talen zoals Python is beschikbaar via plug-ins. Stap 1: Download gratis Visual Studio community 2019 Ga naar https://visualstudio.microsoft.com/ Kies ervoor om de gratis versie van Visual Community 2019 te downloaden of gebruik de directe link:...

Lees meer

Hoe gebruik je capture beelden met PyCharm met behulp van een voorbeeld Python script in Python

  Camera installation instructions     14-12-2023  

Python is een programmeertaal die u kunt gebruiken om uw machine vision-programma te maken. In dit artikel laten we u zien hoe u een Python-voorbeeld kunt downloaden, installeren en gebruiken om afbeeldingen te bemachtigen. We gebruiken het programma PyCharm. Download en installeer benodigde software: Volg deze gids voordat je begint om ervoor te zorgen dat je onze Windows SDK hebt geïnstalleerd en dat je in staat bent om afbeeldingen van de camera te bemachtigen met behulp van de SDK: https://www.vision-camera.nl/QuickStart-5-steps-to-easily-install-a-machine-vision-camera-and-acquire-an-image Nadat u de Daheng SDK hebt geïnstalleerd, worden er verschillende voorbeelden meegeleverd. Deze bevinden zich in de directory C:\Program Files\Daheng Imaging\GalaxySDK\Samples\Python SDK. Download en installeer de Python 3.8...

Lees meer

Daheng Galaxy Viewer om onze industriƫle camera's te programmeren

  Camera installation instructions     14-12-2023  

Het Daheng Galaxy Viewer-programma is het belangrijkste hulpmiddel om de camera te testen en te programmeren. Met Galaxy Viewer is het mogelijk om cameraparameters te wijzigen en op te slaan, en om afbeeldingen te verkrijgen en op te slaan. Het heeft meerdere plug-ins voor extra functies zoals kruisdraden, raster en LUT. We laten u zien wat de mogelijkheden zijn en hoe u de Daheng Galaxy Viewer kunt gebruiken. Stap 1: Installeer de Daheng machine vision camera SDK  ** Sluit de Machine Vision Camera niet aan vóór of tijdens de installatie van de SDK.**  U kunt de nieuwste versie van onze SDK vinden in ons downloadgedeelte. Na het downloaden van de SDK installeert u deze door het bestand uit te voeren dat aan de rechterkant wordt weergegeven.   Zodra de SDK is geïnstalleerd:...

Lees meer

Hoe installeer je Aravis op Linux en hoe verkrijg je afbeeldingen van de machine vision camera

  Camera installation instructions     14-12-2023  

Aravis is een machine vision software kit die is ontwikkeld om gelijktijdig machine vision camera's van verschillende fabrikanten te gebruiken. Aravis is een op object gebaseerde vision-bibliotheek die oorspronkelijk is gemaakt voor Linux om digitale industriële camera's te bedienen en afbeeldingen van deze camera's te verkrijgen. Aravis gebruikt de GenICam API om de machine vision camera's te bedienen en wordt geleverd met een eenvoudige viewer-interface. Het is ook gebouwd als elke andere Meson-build. U kunt Aravis gratis downloaden op GitHub. In dit artikel beschrijven we hoe u Aravis op Linux kunt installeren met behulp van Python en hoe u kunt beginnen met het verkrijgen van afbeeldingen van de industriële camera. Stap 1: Installeer Python en P op uw Linux computer Open de Linux-terminal en voer de...

Lees meer

Hoe gebruik je Kinovea om afbeeldingen op te nemen, vast te leggen, te meten en te annoteren met machine vision cameraā€™s

  Camera installation instructions     13-12-2023  

Kinovea is een open-source video-opname-, meet- en annotatietool, ontworpen voor beeldvisualisatie, opname, meting, annotatie en (hogesnelheids-) bewegingsanalyse. Het stelt de gebruiker in staat om beweging in video's vast te leggen, te vergelijken, te annoteren en te meten. Het kan high-speed camera's opnemen en de opgenomen video in slow motion afspelen. Kinovea wordt gebruikt in veel markten, zoals: Laboratorium (analyseren van foto’s van een microscoop) Industriële automatie (Gebruik de slow-motion functie om mechanische problemen met een machine op te lossen) sport (Bijhouden van de beweging van atleten om techniek te verbeteren) Dit artikel is een stapsgewijze handleiding die uitlegt hoe u Kinovea op uw apparaat installeert, uw opnameparameters instelt en basismetingen en -annotaties uitvoert....

Lees meer

Hoe gebruik je 2ndLook machine vision software?

  Camera installation instructions     13-12-2023  

2ndLook is een eenvoudige software om video's op te nemen met uw industriële camera's. Gefocust op een eenvoudig en gebruiksvriendelijk ontwerp biedt de software een gebruiksvriendelijke manier om video's op te nemen en te bekijken. U kunt video's opnemen in verschillende bestandsvormen, waaronder MP4, RAW of het eigen formaat van 2ndLook: 2ndLook Video Library. 2ndLook is compatibel met alle USB3- en GigE-camera's. Download 2ndLook Je kan 2ndLook downloaden op onze download page . Klik op de link om de download te starten. Bewaar de download, als hij eenmaal is afgelopen start de installer. Start met 2ndLook Nadat u 2ndLook op uw pc hebt geïnstalleerd, gebruik hem dan als administrator. Bekijk de tutorial om de software te leren kennen. Selecteer USB3 Vision of GigE Vision als driver,...

Lees meer

How to use Micro Manager for Microscopy applications

  Camera installation instructions     12-12-2023  

Micro Manager is an open-source software developed to control and automate microscopic applications. Micro Manager was developed to serve as a complete image acquisition and microscope control package, available for Windows, Linux and Mac. Since it is Open Source, it is easy to extend for specific needs (e.g. your own camera drivers). It has a full integration of ImageJ, an image processing package. This article explains how to install and use Daheng cameras with Micro Manager. Installation Before installing micro manager, please make sure that you have installed our SDK first. Check our QuickStart article , for a detailed guide on how to install our SDK. Download micro manager from the official website and follow the instructions. Then Download the Daheng.dll from our download area and copy it to the Micro Manager...

Lees meer

De geschikte lensresolutie selecteren voor de pixelgrootte van uw camera

  Vision Hardware Selection     14-12-2020  

Bij het kiezen van een lens voor uw industriële camera is het belangrijk dat de lensresolutie overeenkomt met de pixelgrootte van uw industriële camera. De lensresolutie wordt gemeten in lijnparen per millimeter (lp/mm). Dit zorgt voor optimale prestaties van uw industriële camera. In dit artikel wordt het principe van lensresolutie in lijnparen per millimeter uitgelegd en hoe u de compatibiliteit met uw industriële camera kunt berekenen.  De lensresolutie in lp/mm en camera pixelgrootte spelen beiden een belangrijke rol bij digitale beeldvorming. Met het aantal lijnparen per mm kunt u de ruimtelijke resolutie van een camera of lenssysteem meten. De pixelgrootte verwijst naar de fysieke grootte van een enkele pixel op de sensor van een beeldcamera.  Neem contact met ons op als u hulp nodig heeft...

Lees meer

How to select a machine vision camera interface (USB3 / GigE / 5GigE / 10GigE Vision)?

  Vision Hardware Selection     02-11-2020  

Machine vision camera Interface whitepaper This article will provide a deeper inside in what the benefits and downsides are of each type of machine vision camera interface, so you can select the right interface for your machine vision application. It has to be noted that GeT cameras only supplies USB 2.0 , USB 3.0 , GigE , 5GigE and 10GigE machine vision cameras and the article will mainly be focused on these five industrial machine vision interfaces. However in the table below we have incorporated also other interfaces to make the overview of industrial machine vision camera interfaces complete.     USB2 USB3 FireWire GigE CameraLink Coaxpress 5GigE 10GigE Bandwidth (Megabyte/s) 40 400 80 100...

Lees meer

Industrial GigE camera with or without Power over Ethernet?

  Vision Hardware Selection     28-09-2020  

When selecting the most suitable Gigabit Ethernet camera for your machine vision project, you should know the differences between industrial cameras with and without Power over Ethernet (PoE). PoE means that the CAT6 network cable simultaneously works as communication and as the power supply for the camera. You can recognise a camera with PoE by the article number with a “-P” at the end. For example, the MER2-630-18GC-P is our 6,3 mega pixel camera with Power over Ethernet, while the MER2-630-18GC has the same image sensor but no Power over Ethernet. Both cameras with PoE and without PoE have their advantages and disadvantages. These are explained below. Why choose for a camera with Power over Ethernet Using a GigE camera with PoE is the most convenient way to power your industrial Gigabit Ethernet camera. You only...

Lees meer

Rolling versus Global shutter

  Vision Hardware Selection     11-08-2020  

Global shutter wordt gebruikt om bewegende objecten vast te leggen, terwijl de Rolling shutter wordt gebruikt om stilstaande beelden vast te leggen. Een Rolling shutter camera is goedkoper, vooral bij resoluties boven de 1,6 Megapixel. Een 12MP Rolling shutter camera, zoals onze MER2-1220-32U3C camera kost ongeveer 200 euro. Een 12MP Global shutter zoals onze ME2P-1230-23U3C camera kost ongeveer 1000 euro. Een Global shutter heeft grotere pixels en een grotere sensor dan een Rolling shutter camera. Hierdoor is een global shutter camera lichtgevoeliger en produceert hij scherpere beelden.  Belichting en sluiter (shutter) De belichtingstijd is de periode tussen het openen en sluiten van de sluiter. Tijdens deze periode val het licht op de fotogevoelige matrix van de chip en treedt het foto-elektrisch effect op,...

Lees meer

NEW! Waterproof aluminium camera housing

  Machine vision market & applications     02-06-2020  

The machine vision camera is a crucial part of industrial automation and protecting your camera in harsh environmental conditions is of great importance. IP67 water and dust proof enclosure Water and dust can not only damage your machine vision camera, but also taint the image quality. GeT Cameras has developed a fully aluminium IP67 camera enclosure: Waterproof Aluminium Camera Housing . This camera enclosure will make your machine vision camera IP67 proof while using GeT Cameras’ standard cables. There is no need for expensive cables with IP67 plugs. Price / Quality ratio This aluminium enclosure costs € 249 and just like other GeT Cameras products it has the most competitive price on the machine vision market. Harsh environmental condition damage will no longer damage your machine vision camera or corrupt the...

Lees meer

How to use (color) C-mount lens filters?

  Camera & Vision techniques     12-05-2020  

The use of (color) C-mount lens filters is to be able to create contrast between colored parts of an object with a monochrome camera to easily detect and measure the specific part of the object. Additionally (color)C-mount lens filters are used to block external-environmental lighting. Why monochrome camera and not color? Because monochrome cameras  are up to 3 times more light sensitive and produce sharper images. (Color)C-mount lens filters can be applied to camera lenses without significant loss of light or image quality. Color lens filter principle Using a Color lens filter to add contrast works on subtraction idea. For this example we take a red bottle cap with red lens filter. The red Lens filters does not brighten up the cap. Instead, the complementary colors and the colors close to the complementary colors are...

Lees meer

Why use industrial machine vision LED lights?

  Vision Hardware Selection     11-04-2020  

Machine vision industrial lights are reliable products which provide constant, non-fluctuating power/light output. They are designed to be used 24/7, providing the best light conditions and machine vision lights are available in many colours to create extra contrast. The machine vision lights have a long-life cycle and therefore the same light with the same specs and output can be purchased for many years. Machine vision lights have a great batch repeatability and minimal led characteristic variations between batches that could cause quality deviations. Industrial lights are powered with constant DC voltage and reliable power sources, therefore there is no flickering. Additionally, it’s possible to over strobe the light, to achieve higher light intensity with the same light (for shorter time). There are several types of...

Lees meer

Installeer onze USB3 / GigE camera's met software van derden? (Halcon | Labview | Cognex | Matlab | Opencv)

  Camera installation instructions     05-02-2020  

Onze USB3 / GigE industriële machine vision camera’s werken met veel machine vision softwarepakketten van derden, zoals MvTec Halcon, NI Labview, Cognex Vision Pro, Matlab en OpenCV. We leveren u gedetailleerde handleidingen waarin wordt uitgelegd hoe u onze camera’s installeert en bedient met deze software. De handleidingen zijn beschikbaar voor MvTec Halcon, NI Labview, Cognex Vision Pro, Matlab, OpenCV en Arm Boards Software. Stap 1: Downloadtoegang aanvragen Ga naar het menu en klik op downloads. Op deze pagina vragen we u om uw e-mailadres in te voeren en u wordt direct doorgestuurd naar onze downloadpagina. Stap 2: Download het ZIP bestand Als u op de 13e link klikt, download u het zip bestand. U kunt ervoor kiezen om dit bestand op uw computer op te slaan of om deze map uit te pakken....

Lees meer

Quickstart: 5 stappen om eenvoudig een machine vision camera te installeren en een beeld te verkrijgen

  Camera installation instructions     19-01-2020  

In deze QuickStart leggen we in 5 eenvoudige stappen uit hoe u een machine vision camera van Daheng Imaging installeert. Dit artikel is gebaseerd op een setup met een Windows pc en een USB3 of GigE machine vision camera. Voor alle andere besturingssystemen kunt u de manuals in onze downloadsectie gebruiken. Benodigde producten: Machine vision camera, lens, datakabel. (externe voeding indien GigE non POE camera). Stap 1: Installeer Windows SDK voor Machine Vision Camera **Sluit alstublieft de machine vision camera niet aan vóór of tijdens de installatie van de SDK** Download de SDK voor onze machine vision camera's . U kunt de nieuwste versie van onze Windows SDK (Windows SDK USB2+USB3+GigE (inclusief Directshow) Galaxy) vinden in onze downloadsectie. Installeer de SDK nadat u deze heeft...

Lees meer